Boom cans Amplified Lower Speakers Service Manual download pdf

-J06051 REV. 2014-11-01

AMPLIFIER INSTALLATION KIT FOR BOOM! AUDIO STAGE II

FAIRING LOWER SPEAKERS

GENERAL

Dealer installation is recommended. Radio EQ update using

the Digital Technician

II diagnostic tool is:

• Recommended before speaker INSTALLATION

• Required before audio system OPERATION.

• Only available through authorized Harley-Davidson

dealers.

Kit Number

76000586

Models

For model fitment information, see the P&A retail catalog or

the Parts and Accessories section of www.harley-davidson.com

(English only).

This kit does not fit Twin-Cooled models.

This kit is not compatible with premium bag liners. Fitted

saddlebag linings require trimming to accommodate amplifier

mount and harness cover.

Installation Requirements

This kit must be installed:

• Before installation of the Boom! Audio Stage II Fairing

Lower Speaker Kit (Part No. 76000353).

• After installation of a PRIMARY fairing-mounted amplifier.

The amplifier (Part No. 76000277A) installed with this kit must

be purchased separately from a Harley-Davidson dealer.

If installing more than TWO amplifiers, an AUDIO IN Three-

Way Y Connector (included in THIS kit) AND a Battery+ Three-

Way Y Connector (Part No. 70270-04A, available separately)

are needed.

The rider's safety depends upon the correct installation

of this kit. Use the appropriate service manual procedures.

If the procedure is not within your capabilities or you do

not have the correct tools, have a Harley-Davidson dealer

perform the installation. Improper installation of this kit

could result in death or serious injury. (00333a)

NOTE

This instruction sheet references service manual information.

A service manual for this year/model motorcycle is required

for this installation. One is available from a Harley-Davidson

dealer.

Electrical Overload

It is possible to overload your vehicle's charging system

by adding too many electrical accessories. If the combined

electrical accessories operating at any one time consume

more electrical current than the vehicle's charging system

can produce, the electrical consumption can discharge

the battery and cause damage to the vehicle's electrical

system. See an authorized Harley-Davidson dealer for

advice about the amount of current consumed by addi-

tional electrical accessories or for necessary wiring

changes. (00211c)

When installing any electrical accessory, be certain not

to exceed the maximum amperage rating of the fuse or

circuit breaker protecting the affected circuit being modi-

fied. Exceeding the maximum amperage can lead to elec-

trical failures, which could result in death or serious injury.

(00310a)

The amplifier installed with this kit requires up to 8 amps

more current from the electrical system.

Kit Contents

See Figure 11 and Table 1.

PREPARATION

To prevent accidental vehicle start-up, which could cause

death or serious injury, remove main fuse before pro-

ceeding. (00251b)

NOTE

• WITH security siren: With security fob present, turn

ignition switch ON. See the service manual. After system

is disarmed, turn ignition switch OFF. IMMEDIATELY

remove the main fuse.

• WITHOUT security siren: See the service manual.

Remove main fuse. Turn ignition switch OFF.

Disconnect negative (-) battery cable first. If positive (+)

cable should contact ground with negative (-) cable con-

nected, the resulting sparks can cause a battery explosion,

which could result in death or serious injury. (00049a)

1 of 8-J06051

Many Harley-Davidson

Parts & Accessories are made of plastics and metals which can be recycled.

Please dispose of materials responsibly.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - FAIRING LOWER SPEAKERS

-J06051 REV. 2014-11-01AMPLIFIER INSTALLATION KIT FOR BOOM! AUDIO STAGE IIFAIRING LOWER SPEAKERSGENERALDealer installation is recommended. Radio EQ

Page 2 - AMPLIFIER INSTALLATION

When servicing the fuel system, do not smoke or allowopen flame or sparks in the vicinity. Gasoline is extremelyflammable and highly explosive, which

Page 3 - ALL applications:

4. Use the template to cut the openings for the upper four-way flanged connector [289-2A].a. Place template on saddlebag again. Align thegrommet and l

Page 4

123is07750a1. Area to be cleaned2. Amplifier bracket3. Tape strip (4)Figure 6. Amplifier Bracket Installation123is077511. Amplifier2. Pin stud3. Gromm

Page 5 - SADDLEBAG WIRING

4. Temporarily install the right saddlebag into the supportassembly.a. Confirm that the vehicle-side harness connectorscomfortably reach the saddlebag

Page 6 - COMPLETION

12is077551. Clip, push-in (3)2. Amplifier coverFigure 10. Amplifier Cover4. Install the saddlebags. Plug in all saddlebag connectors.5. Attach the new

Page 7 - SERVICE PARTS

SERVICE PARTS[149][289-1A][289-2A][289-1B][289-2B][296][37LW][37LT][36LW][36LT][160A/B][160][91A] [91B][43][GND][GND][296]67A2111121310B15431058989714

Page 8

SERVICE PARTSTable 1. Service PartsPart NumberDescription (Quantity)Item76000282AAmplifier bracket1926Screw, hex socket button head (2),21/4-20 x 0.62

Boom cans Amplified Lower Speakers Service Manual

Browse online or download Service Manual for Soundbar speakers Boom cans Amplified Lower Speakers. Boom cans Amplified Lower Speakers Service manual User Manual

Summary of Contents

More documents for Soundbar speakers Boom cans Amplified Lower Speakers

Comments to this Manuals